Audison Bit Ten

£279.00

The Audison Bit Ten should be at the heart of any car audio upgrade, providing seamless integration with any factory fitted car stereo. It is our processor of choice..!

  • Audio DSP and converters
  • 32 bit Cirrus Logic (Clock speed: 147 MHz) Digital Signal Processing chip and A/D
  • D/A converters working in PCM at 48 kHz with 24 bit resolution. The processor speed
  • allows the user to hear and verify in real time the changes applied during the tuning.
  • Audio Inputs
  • 4 independent high-level channels with automatic summing capability;
  • 1 analog low-level stereo auxiliary input;
  • 1 high-level momentary audio interrupt input (with priority) on Phone Mute cable (settable
  • through PC).
  • Audio Outputs
  • 5 independent analog PRE channels featuring adjustable level.
  • Control Connections
  • 1 USB /B (2.0) connector for PC connection;
  • 1 AC Link control bus connectors for DRC;
  • 1 input for external Mute (settable through PC).
  • The Audison bit Ten is a multi-function digital processor featuring analog input, capable of transforming ordinary OEM or after-market system into a high-performance system.
    Provided with a 32 bit, 147 MHz clock speed DSP as well as 24 bit A/D and D/A converters, bit Ten is controlled by a software especially developed for signal treatment according to the vehicle acoustic peculiarities.
    Setting the parameters of each input single channel, setting the delays according to the listening position, adjusting crossovers and equalizers for each of the 5 output channels; all of these operations can be managed by the PC.
    During the installation phase, after converting the analog signal into digital, bit Ten automatically reconstructs a digital full-bandwidth stereo signal; de-equalizes the frequency response and, if necessary, reconstructs the central and sub-woofer channels.
    The user can configure the output mode of each channel relative to the installed system.
    It is designed to be connected with the DRC Digital Remote Control (optional).

    Configuration
    Guided procedure that, thanks to a wide range of set names, provides the ability to assign
    each component to the bit Ten connections and automatically coordinate their functioning.
    Turn-on Controls
    ART, Automatic Remote Turn on/off, selectable from Hi-Level Front L. The ART can be
    enabled through an external switch;
    Through the Remote IN;
    Through the car ignition key with memory function;
    Through the DRC (optional);
    Automatically through the hands-free phone kit.
    In/Out Volume
    Input sensitivity manual adjustable for the Master Hi-Level inputs (with supplied Test CD);
    Manual input sensitivity adjustment for auxiliary inputs;
    Independent level control for each output channel for system fine tuning (-40 ÷ 0 dB).
    De-equalization
    Automatic de-equalization of signal fed into the high-level inputs (with supplied Test
    CD) if necessary. It can also be performed without the PC.
    Equalizers
    31-band graphic equalizer (1/3 Oct.; ±12 dB) for each output channels.
    Crossover Filter
    Filter typology: selectable; Hi-pass, Lo-pass, Full Range, Band pass with independent
    selectable cut-off slope.
    Cut-off frequency: 70 steps available from 20 Hz to 20k Hz;
    Cut-off slope: selecable; 6 to 24 dB/Oct.;
    Selectable alignment: Linkwitz or Butterworth;
    Mute: selectable for each output (On/Off);
    Phase: selectable for each output (0°/180°);
    Signal channels reconstruction
    It can reconstruct a stereo output signal from a multi-channel input signal. In addition it can
    reconstruct rear, centre and subwoofer output channels from a stereo input.
    Time Alignment
    Guided procedure for the speaker distance data entry with an automated calculation (distance
    to time) for each channel for accurate delay times. System also provides for manual fine
    tuning of delay (0.02 ms fine set).
    DRC (optional)
    Master Volume, Subwoofer Volume, Balance and Fader controls, Input selection,
    Memory selection, Adjustable display brightness.
    Memory
    2 presets separately managed and recalled by the DRC (optional).
    bit Ten software
    Windows (XP, 7 and Vista) based software with “Standard” and “Expert” operating modes;
    Screen resolution: 1024 x 600 px min.

    Power Supply
    Input Stage
    Output Stage
    Connection
    Signal Stage
    Crossover N.5 (one each output channel)
    Equalizer
    Time Alignment
    Size
    Voltage 11 ÷ 15 VDC
    Idling current 0.4 A
    Switched off without DRC 2.5 mA
    Switched off with DRC 4 mA
    Remote IN voltage 7 ÷ 15 VDC (1.3 mA)
    Remote OUT voltage 12 VDC (130 mA)
    High Level (Speaker) FL - FR - RL - RR - PHONE IN
    Low Level (Pre) AUX IN
    Low Level Pre (Default) FRONT L/R, REAR L/R, SUB
    From / to personal computer 1 x USB / B (1.1/2.0)
    Distortion-THD @ 1 kHz, 1V RMS Output 0.005 %
    Bandwidth @ -3 dB 10 ÷ 22k Hz
    S/N Ratio @ weighted
    Master Input 95 dBA
    Aux Input 96 dBA
    Channel Separation (@ 1 kHz) 85 dB
    Input sensitivity (Speaker In) 2 ÷ 15 V RMS
    Input sensitivity (AUX in) 0.6 ÷ 5 V RMS
    Input sensitivity (PHONE) 2 ÷ 15 V RMS
    Input impedance (Speaker In) 2,2 k& 937;
    Input impedance (AUX in) 15 k& 937;
    Input impedance (PHONE) 2,2 k& 937;
    Max Output Level (RMS) @ 0.1% THD 4 V RMS
    Mode Full / High Pass/ Low Pass/ Band Pass
    Type and slope Linkwitz @ 12/24 dB
    Butterworth @ 6/12/18/24 dB
    Crossover frequency 68 steps @ 20 ÷20k Hz
    Phase control 0° ÷ 180°
    Hi-Level Input (Speaker In) Automatic De-Equalization
    Outputs N.5 Graphic ± 12 dB @ 31 Band ISO 1/3 Oct. 20 ÷ 20k Hz
    Distance 0 ÷ 510 cm / 0 ÷ 200.8 in.
    Delay 0 ÷ 15 ms
    Step 0,08 ms; 2,8 cm / 1.1 in.
    Fine set 0,02 ms; 0,7 cm / 0.27 in.
    W x H x D (mm / in.) 191 x 34 x 131 / 7.51 x 1.33x 4.76
    Weight (kg / lb.) 0,6 /1.322

      Send Us Your Review of Audison Bit Ten

    Contact RAM Mobile about Audison Bit Ten Installation