Tens of thousands have relied on V-Power amplifiers for dependable, quality power. Now in their fourth generation, V-Power amplifiers carry on this heritage and prove that playing strong never looked our sounded better. Yes, it is possible to improve upon a good thing.

  • Total Max Power: 640 W
  • 75W RMS x 4 (2Ω, 14.4V, ≤1% THD+N)
  • 50W RMS x 4 (4Ω, 14.4V, ≤1% THD+N)
  • Same power in a 40% smaller chassis
  • Evolution to Class D digital platform
  • New snap-on terminal covers for easy installation
  • Raising the Bar
    The new V-Power products are now Class D digital amplifiers, resulting in a huge efficiency gain versus their predecessors without draining your battery or your pockets. Class-D provides continuous clean power to your speakers, operating at 80% efficiency far greater than conventional Class A or B amplifiers. Translation: Enjoy cleaner bass, even during extreme power demands.

    Big Power, Small Package
    V-Power amplifiers are known for their compact size, but donít underestimate their power capacity. Although they have a 40% smaller footprint than their predecessors, they produce the same amount of power as before. Get the power you need, even if you have limited installation space.

    Non Shut-Down Design
    Even if you pound your music for a long time, these amps wonít shut down. They use a Thermal Management Processor to make sure the heat level never gets too high. No distortion, no interruptions!

    Dual Feedback Modulation
    Dual internal error correction technology Ė which had previously only been available in the PDX and X-Power amplifiers, is now integrated in V-Power mono amplifiers. The audio input signal is analysed, compared, and corrected twice dynamically as the signal is processed through the amplifier. The result is amplifiers with the widest frequency response, higher damping factor, and lowest noise in its class.

    Exceptionally Simple Sound Upgrade
    The V-Power's 4-channel speaker level inputs connect directly to any head unit, without the need for external converters. This makes the V-Power amplifiers ideal for upgrading factory and aftermarket systems. The flush mount controls make for easy installation. The terminal covers conveniently snap-on without the need for additional tools, to protect the wiring connections while creating a clean, finished appearance.

    Proven Power
    Each V-Power amplifier comes with its very own birth-sheet. V-Power amplifiers are tested and documented to show their true actual output.

    Terminal Layout Two-Sided
    Integrated Wire and Mounting Screw Terminals
    Amplifier Type Class-D (Digital)
    Channel Design 4/3/2-Channel
    Power Supply Design DC-DC PWM Power Supply
    Power Supply MOSFET
    Pre-Amp Stage Discrete
    Final Outputs Power MOSFET
    Crossover Variable Lowpass & Highpass Filter
    Gain Control Continuously Adjustable Gain Control
    Bass EQ
    Remote Turn On Remote Sensing Function (for Speaker Level Input)
    Low-impedance Possibility
    Current Protection Over-Current, Over-Voltage, Under-Voltage and Thermal Protection
    Board Circuitry S.T.A.R. Circuit
    RCA Output Non-Fading Pre-Amp Output (4 Volts)
    Speaker-Level Inputs 4-channel Speaker Level Inputs
    Power Indicator Top Mounted Blue LED Power Indicator
    Thermal Control Multi-stage Power Limits
    Max Power Output Ratings
    Total Max Power 640 W
    RMS Power Ratings
    Per channel into 4 Ohms 50W RMS x 4 (14.4V at <1% THD+N)
    Per channel into 2 Ohms 75W RMS x 4 (14.4V at <1% THD+N)
    Sound Tuning
    Crossover Frequency (LPF/HPF) 50Hz-400Hz , -12dB/oct.
    EQ (Equalizer) Bass EQ (fc=50Hz) 0 to +12dB for CH-3/4
    Foot Print (WxHxD) mm 200 x 55 x 200 mm
    Heat Sink (WxHxD) mm 165 x 55 x 200 mm
    Power Requirements 14.4 V.DC (11-16V allowable)
    Input Sensitivity (RCA Input) 0.2 - 4.0 V
    Input Sensitivity (Speaker Level Input) 0.5 - 10 V
    Input Impedance >10k ohms
    Frequency Response (+0, -1dB 1W into 4 Ohms) for Subwoofer
    THD+N (10W into 4 Ohms) 0.03 %
    THD+N (10W into 2 Ohms) 0.05 %
    THD+N (Rated Power into 4 Ohms) 0.08 %
    THD+N (Rated Power into 2 Ohms) 0.1 %
    Damping Factor (10W into 4 Ohms at 100Hz) >90
    Signal to Noise (1W into 4 Ohms) >81 dB
    Signal to Noise (Rated Power into 4 Ohms) >98 dB
    Weight 1.7 kg

      Send Us Your Review of Alpine 4 CHANNEL POWER AMPLIFIER - MRV-F300

    Contact RAM Mobile about Alpine 4 CHANNEL POWER AMPLIFIER - MRV-F300 Installation