Bassface black SPL6C.1 6.5" Inch 17cm 4Ohm Component Speaker & Tweeter Kit 450w RMS


The BLACK series speakers are bursting with audiophile build specs. Large KSV voice coils and oversize magnets increases magnetic force. Cast Aluminium baskets with extensive cooling for the VC provides a significant reduction in power compression, this means they play louder for longer with more power.

  • Cast Aluminium Basket Reduces Mechanical Distortion
  • Oversize 1.5 Voice Coil For High Power Handling
  • High Power Crossover With Hi-Freq Attenuation Switch
  • Extra VC Cooling Vents Decrease Power Compression
  • Woven Black Fibre Cone Provides Superior Dynamics
  • Over-hung Non Fatiguing Rubber Surround
  • Rigid Large Dustcap Increases Cone Stiffness
  • Large Clear Silk Dome Tweeter
  • High Magnetic Flux Motor Design
  • Sibilance Minimising Tweeter Protection
  • Engineered For SQ OEM Location Install Use
  • Power compression is often overlooked at the price of significantly reduced output when running at high power, due to increased resistance from head build up in the motor assembly. This also affords the BLACK series speakers a much more open and natural sound. We made the suspension as light weight as possible to retain amazing cone control. This gives the midrange units high sensitivity enabling them to be high effective across a broad spectrum of power amplifiers. The tweeters use Neodymium magnets and ferrofluid cooling. This gives them a slimmer profile without loss of control. The domes are 100% pure silk with translucent finish which looks almost as good as it sounds! These are designed from the bottom up to impress even the most discerning ear. We are confident that these will surpass your expectations for even high end audio products. The BLACKSPL5C.1 and BLACKSPL6C.1 both have higher power handling to thier Coaxial counterparts. With more advanced crossover networks allowing for different tweeter positions with a tweeter dip switch. Giving you -3db 0db and +3db notches. We also revised the components so only the best quality components make up the crossover, affording them more power handling an better frequency control.

    Tweeter Data
    Recommended Cable PSC18.1
    Overall Depth (mm) 30
    Mounting Depth (mm) 17
    Front Protrusion From Mounting Plane (mm) 13
    Overall Diameter (mm) 30
    Installation Cutout Diameter (mm) 50
    Magnet Type Neodymium
    System Maximum Power (Watts) (Using Pair Of Tweeters Not Necessarily Included) 300
    System RMS (Watts) (Using Pair Of Tweeters Not Necessarily Included) 150
    Frequency Response (Hz) 3500-23000
    Impedance (Ohm) 4
    Speaker Data
    Speaker Maximum Recommended Power (Watts) (One Speaker, Using Appropriate Crossover) 300
    Speaker Maximum Recommended Power RMS (Watts) (One Speaker, Using Appropriate Crossover) 150
    Overall Diameter With Lugs (mm) 165
    Overall Diameter With Grilles (mm) 180
    Overall Diameter (mm) 165
    Magnet Diameter (mm) (Including Magnet Protector Where Applicable) 105
    Installation Cutout Diameter (mm) 145
    Grille Depth (mm) 30
    Overall Depth (mm) 81
    Mounting Depth (mm) 72
    Front Protrusion From Mounting Plane (mm) 9
    System Frequency Response (Hz) (Indicative Of Usable Range But Not Suitability) 37-23000
    Impedance (Ohm) (Nominal) 4
    Recommended Cable PSC12.2

      Send Us Your Review of Bassface black SPL6C.1 6.5" Inch 17cm 4Ohm Component Speaker & Tweeter Kit 450w RMS

    Contact RAM Mobile about Bassface black SPL6C.1 6.5" Inch 17cm 4Ohm Component Speaker & Tweeter Kit 450w RMS Installation